Services
Aerial Lift TrainingForklift Operator Certification
Instructor Courses
Mobile Crane Operator Certification
Online Training
Crane Operator Training
Overhead Crane Training
Rigging and SignalPerson Training
All Purpose Crane Training offers crane operator training on-site or off-site. Providing National accredited crane operator certification meeting OSHA ANSI standards for crane operators to become certified.
1926.1401
1926.1402
1926.1403
1926.1404
1926.1405
1926.1406
1926.1407
1926.1408
1926.1409
1926.1410
1926.1411
1926.1412
1926.1413
1926.1414
1926.1415
1926.1416
1926.1417
1926.1418
1926.1419
1926.1420
1926.1421
1926.1422
1926.1423
1926.1424
1926.1425
1926.1426
1926.1427
1926.1428
1926.1429
1926.1430
1926.1431
1926.1432
1926.1433
1926.1434
1926.1435
1926.1436
1926.1437
1926.1438
1926.1439
1926.1440
1926.1441
1926.1442
- (a) Permanently installed overhead and gantry cranes. The requirements of 1910.179, except for 1910.179(b)(1), and not the requirements of this subpart cc, apply to the following equipment when used in construction and permanently installed in a facility: overhead and gantry cranes, including semi gantry, cantilever gently, wall cranes, storage bridge cranes, and others having the same fundamental characteristics.
- (b) Overhead and gantry cranes
- (1) This paragraph applies to the following equipment when used in construction and not permanently installed in a facility: overhead and gantry cranes, overhead/bridge cranes, semi gantry, cantilever gently, wall cranes, storage bridge cranes, launching gently cranes, and similar equipment having the same fundamental characteristics, irrespective of whether it travels on tracks, wheels, or other means.
- (2) The following requirements apply to equipment identified in paragraph (b)(1) of this section:
- (i) Sections 1926.1400 through 1926.1414; 1926.1417 through 1926.1425; 1926.1426(d), 1926.14277 through 1926.1434; 1926.1437, 1926.1439, and 1926.1441.
- (ii) He following portions of 1910.1799:
- (A) Paragraphs (b)(5).(6),(7): (e)(1).(3),(5),(6); (f)(1),(4); (g); (h)(1),(3); (k); and (n) of 1910.179.
- (B) The definitions in 1910.179(a) except for "hoist" and "load" for those words, the definitions in 1926.1401 apply.
- (C) Section 1910.179(b)(2), but only where the equipment identified in paragraph (b)(1) of this section (1926.1438) was manufactured before september 19, 2001.
- (iii) For equipment manufactured on or after september 19, 2001, the following sections of asme b302-2005 (incorporated by reference, see 1926.6) apply: 2-1.3.1; 2-1.3.2; 2-1.4.1; 2-1.6; 2- 1.7.2; 2-1.8.2; 2- 1;9.1; 2-1.9.2; 2-1.11; 2-1.12.2; 2-1.13.7; 2- 1.14.2; 2-1.14.3; 2-1 .14.5; 2-1.15.; 2-2.2.2; 2-3.2.1.1. In addition, 2-3.5 applies, except in 2-3.5.1(b), "29 cfr 1910.147" is substituted for "ansi z244.1
